Late 1940's / Early 1950's Zippo Restoration

Taking a break from all the DIY-heavy home improvement projects, I found this rusted out Zippo lighter at a flea market.

I've always been a fan of Zippos, their style (and that unique sound) is incredibly iconic, so I figured I'd have a crack at restoring it.

Plus I still have a bunch of spares left over from the trench lighter project I did a while back.

Before starting, I did some research to try and put a date on the lighter, just in case it was something super-rare.

 

 

 

 

The first thing to so is to check the stamp at the bottom of the case:

According to the table provided by Zippo themselves, based on the logo type and the patent number, this lighter was manufactured in the 1937-1950 date range.

Digging through some other online resources, I found that it could be dated further by the chimneys number of holes, and the pattern of the flint wheel.

Depending on the source, the chimney having 8 holes per side dates it as being from late 1946 or 1947 onward.

The diagonal-cut flint wheel puts it also at 1946 onward.

Finally, the hinge (again, depending on the source), puts it at either 1948 or 49 onward

So between all that, it looks most likely that this lighter was produced between 1948-1950.

It's pretty cool to know the lighter has some history to it, but it doesn't make it a massively rare artefact.

Removing the rust

The rust on one side in particular was quite thick. To remove it I started with a small rotary tool wire wheel, then moved to some high-grit sanding discs, before some wet and dry sanding by hand to even out some scratches, finally finishing up with a number of passes with the buffing wheel and polishing compound.

As much as I am trying to preserve the original chromed finish, it was clear even before starting that it had worn through in places - I was merely trying to not make it any worse.

However with that lot done, although it's not exactly 'showroom' quality, the lighter has it's shine back, but retains a lot of it's characterful aging which suits it's age.

Flints & Wicks

The obvious thing to note is that it's not functional. To start with, there was no flint to make a spark. Thankfully the flint spring was still there, so adding one of my spares was all it took to get it sparking again.

The wick had been worn down to nearly nothing as well. I thought that I would likely need to replace it, so had a spare to hand, but it appears as though there was still plenty of wick remaining to pull through. It's quite possibly that the previous owner just never knew to do this - or had lost the flint before it was an issue.

Then all that was left was to add fuel, and:

Old Hand Saw Restoration

I found these old saws in my local scrap store for a quid. I've always been a fan of the old-fashioned aesthetic of wooden handles. So being just a quid, I thought I'd grab them, although I wasn't really sure what I wanted to do with them.

Before

A post shared by Anthony (@darkmidnight_diy) on Mar 14, 2017 at 6:23am PDT

The Blades
The blades were very rusty, and I wasn't sure if they'd be salvageable. I was only really after the wooden handles anyway, but thought it'd be worth a shot restoring them.

One of the "old-wives tale"-type solutions for rust is white vinegar. I was sceptical, but it's a cheap option, so I gave it a shot, and it worked surprisingly well.

It takes some time, but takes little actual working time - I just set up the blades soaked in the vinegar (I found it easier to wrap the blades in kitchen roll/tissue paper and soaking that, rather than trying to find a suitably sized container).

I did that first thing in the morning, left them most of the day and later rinsed them off and scrubbed the blades. It got the worst off, but there was still a few spots of rust that remained. For that I used a wire brush.

The screws were brass, and cleaned up easily with Brasso.

The Handles
The handle of the tenon saw was in the worst state of the two - removing the blade revealed quite a large crack running from the near screw hole to the hand opening. During disassembly this caused a fragment to break away, but I was able to glue it back neatly with Superglue and it's not noticeable unless it's being looked for.

The flat sides of the handle I sanded with an orbital sander, but sanding the curved areas required a Dremel and a lot of patience.

Once sanded both handles were stained with a redwood stain, applied using a cloth rather than a brush (I find this highlights the natural woodgrain better).

After

A post shared by Anthony (@darkmidnight_diy) on May 3, 2017 at 6:27am PDT

Now they're restored, I'm still not entirely sure what to do with them. I have plenty of other saws, so it's not like I'll particularly need them for actual work, so I'll likely just use them for some artsy display or something in the workshop.

Side note: After removing all the rust, I discovered this faint engraving on the side of the tenon saw. It says PT2250, and appears hand-engraved.

It's very faint and difficult to photograph clearly, but it's hand written and says "PT 2250". Wonder what it means?